Godex EZ-DT2 Instrukcja Użytkownika

User’s Manual EZ-DT-2 / EZ-DT-4 P/N. 920-012511-03 Rev. A, 08.2009

2. Printer Installation 2-1. Label Installation 1. Place the printer on a horizontal surface and open the Top Cover. 2. Press and release the loc

7. Put the label under the Label Guide and stretch it frontward. 8. Pull the Label Guide inward and make it fit the edge of label. 9. Close the T

2-2. Label Roll Core Switch 1. Pull the Label Roll Holder to the topmost and lift the Label Roll Core upward. 2. Turn the Label Roll Core outward a

2-3. PC Connection 1. Please make sure the printer is powered off. 2. Take the power cable, plug the cable switch to the power socket, and then conn

2-4. Driver Installation 1. Insert product CD to your computer’s CD Drive and find the "Windows Drives" folder. 2. Select the icon of dr

6. Select connection port. 7. Enter the printer name and set printer sharing option. 8. A description page of printer settings will be displayed

3. Accessory 3-1. Stripper Module Installation 1 Stripper Module 2 Screw x 2pcs 【Note1】 Please power off the printer before installing the stripper

EZ-DT-4 EZ-DT-2 5. Turn the printer around and tighten screws to fix the Stripper in location. 5. Loose the screw of Bottom Case Cover and open it.

10. Flip the stripper downward to open it. 11. Follow the instruction on Chapter 2-1 to install the label. 12. Peel off the first label, and feed

3-2. Cutter Module Installation 1 Cutter Module 2 Screw x 2pcs 21 【Note1】 Please power off the printer before installing the cutter module. 【Note2】 D

Safety Instructions Bitte die Sicherheitshinweise sorgfältig lesen und für später aufheben. 1. Die Geräte nicht der Feuchtigkeit aussetzen. 2. Be

Z-DT-4 E EZ-DT-2 5. Turn the printer around and tighten sc orews t fixthe Cutter in location. 5. Loose the screw of Bottom Case Cover and open i

3-3. EZ-DT-2 t Module Installation Ethernet CaEtherneble 1.8M 1 2 Module Connection Wire 3 Bracket 4 Ethernet module 5 Ethernet Back Panel 6 B

8. Unscrew the Ground wire screw and r re. emove the Ground wi 9 screws on both sides of . Loosen hexagonalRS-232 port. 10. Remove Standard Back

16. Plug the connector of the Module Connection Wire into the so cket on Ethernet module. 17. Use power connector cable to push all connection wires

3-4. EZ-DT-4 Ethernet Module Installation 1 Ethernet module 2 Ethernet Back Panel 3 Module Connection Wire 4 Secure Screw*1 5 Ethernet Cable 1.8

9. Install the Ethernet Back Panel to the printer. 10. al 11. screws. Push the mainboard back to originposition. Tighten the hexagonal 12. Alig

4. Printer Setting 4 After pre feed the media (according to media type) to the s ith continuous media, pressing the FEED key will feed the media out

4-4. Self-Test The Self-Test page helps user to figure out whether the printer is operating normally. Below are ns about the content of Self-Test page

4-5. Error Messages LED Light Beep Description Solution Red (Flash) None Print head temperature high. Wait for the print head temperature drops t

5. Maintenance and Adjustment 5-1. Print Head Module Installation / Remo1. Open the top cover e the d Lift, w on the left side of Top Cover. 【Note】

Safety Instructions Please read the following instructions seriously. 1. Keep the equipment away from humidity. 2. Before you connect the equipme

5. Remove the Print Head Screws, 6. From the underneath of the Print Head Bracket, 7. After new print head is installed, tighten the Print Head Sc

5-2. Thermal Print Head Cleaning Uncle y be caused by dusty print head, ribbon stain or label liner glue. Therefore when printing, it’s necessary to k

5-4. Black Mark Paper W aper width is equal to the maximum width of p 18mm for EZ-DT-4), the error may occur since the b e detected by sensor someti

5-5. Troubleshooting Problem Recommended Solution LED light does not light up after power on the printer  Check the power connector LED light indic

Appendix 1. EZ-DT-2 Certifications EZ-DT-2/EZ-DT-4 User’s Manual 33

EZ-DT-2/EZ-DT-4 User’s Manual 34

EZ-DT-2/EZ-DT-4 User’s Manual 35

EZ-DT-2/EZ-DT-4 User’s Manual 36

EZ-DT-2/EZ-DT-4 User’s Manual 37

2. EZ-DT-4 Certifications EZ-DT-2/EZ-DT-4 User’s Manual 38

1. BARCODE PRINTER...4 1-1. Printer Accessories...

EZ-DT-2/EZ-DT-4 User’s Manual 39

EZ-DT-2/EZ-DT-4 User’s Manual 40

EZ-DT-2/EZ-DT-4 User’s Manual 41

EZ-DT-2/EZ-DT-4 User’s Manual 42

EZ-DT-2/EZ-DT-4 User’s Manual 43

1. Barcode Printer 1-1. Printer Accessories After unpacking, please check the accessories that come with the package, and store appropriately.  Barc

Download Fonts Bitmap fonts 90°, 180°, 270° rotatable, single characters 90°, 180°, 270° rotatable Asian fonts 90°, 180°, 270° rotatable and 8 times

1-3. Communication Interface Serial Interface Serial Default Setting : 9600 baud rate､no parity､8 data bits､1 stop bit､XON/XOFF protocol and RTS/CTS。

1-4. Printer Parts 24153 1. LED Light 2. FEED Key 3. Top Cover 4. Power Switch 5. Cover Open Button 123654 1. Print Head Lift 2. Label Roll Hold

321 1. Platen Cover 2. Label Sensor 3. Platen Roller 1324 1. Power Socket 2. USB Port 3. Fan-Fold Label Insert 4. Serial Port (RS-232) 12 1. Bottom